We noticed you're browsing in private or incognito mode.

To continue reading this article, please exit incognito mode or log in.

Not a subscriber? Subscribe now for unlimited access to online articles.

Emerging Technology from the arXiv

A View from Emerging Technology from the arXiv

Slow Drug Release From Cellular Automaton Pills

Modelling pills as if they were cellular automaton could change the way tablets are designed and made

  • August 27, 2012

The pharmaceutical industry uses various systems for delivering drug doses over time. One of these is the matrix tablet. 

These are made by mixing the drug in powder form with an inactive filler ingredient and a polymer binder, then compressing and heating the mixture to form a hard pill. When ingested, these tablets dissolve and crumble, releasing the drug into the body.

An important question is how quickly the drug enters the body. One way to assess this is experimentally, using an analogue of the human digestion system in a wetlab. But this process is messy, time consuming and expensive.

Today, Peter Hinow at the University of Wisconsin and a few pals suggest a new way to do this by computation. Their idea is to model a matrix tablet is if it were a pile of cubic building blocks, where each element is a cube of the active drug, the filler, a polymer binder, empty space or water. In fact, the whole system is like a three-dimensional chemical lego set.

By themselves, each block is stable but the cubes react with water in different ways. The empty blocks fill up at a certain rate while the filler, binder and drug blocks dissolve at certain rates. Once dissolved, these cubes become water blocks. 

However, the rates depend on the number and type of neighbouring blocks– for example, a drug cube will dissolve more quickly when completely surrounded by water compared with when it shares a single face with a neighbouring cube of water. 

It’s easy to see the similarity with a cellular automaton, where the state of each cell in the next round depends on its neighbours in the previous round. Knowing the various rates gives a straightforward way of calculating how the pill releases its drug over time.

An important factor, of course, is how the blocks of drug, binder, filler and empty space are distributed in a pill to start off with. Hinow and co assume they are distributed randomly in the proportions given in the pill’s formulation. 

They then calculate how the process of drug release progresses on an iterative basis. It starts with the pill surrounded completely with water. The pill’s outer blocks then start to dissolve or fill with water. The model even allows for the pill fragmenting into parts. 

The results, say Hinow and co, agree well with the values measured by experiment.  ”We find that our simulations can reproduce experimental drug release profiles,” they say. And the simulations are much cheaper and easier to perform than the wetlab work.

Of course, there are limitations. The model assumes that the rate at which the filler and drug dissolves are independent but this may not always be the case, particularly when these substances are adjacent. 

The model also assumes that a block of drug can dissolve completely in a block of water, which may not be the case either. These are factors that will have to be ironed out.   

However, the work has important potential. Perhaps the most interesting aspect is how it could influence the way slow release pills are made in future. Hinow and co say the model could help pharmaceutical companies  formulate and produce their pills more quickly because it does away with the need for some many wet tests.

But there is other potential here too. The cellular automaton approach suggests the possibility of far more complex drug release mechanisms, making different drugs available at different times for example. 

But if pills really do work like cellular automaton (as opposed to being simulated by them) there is possibility of logic operations–if X then Y-type behaviour–which turns pill into chemical computers. 

It’s not beyond the realms of possibility to imagine a pill manufacture using a kind of 3D printing technique which can create the complex assemblies necessary for this kind of work.

Far-fetched? Clearly. But exciting nonetheless.

Ref: arxiv.org/abs/1208.3447: Swallowing A Cellular Automaton Pill: Predicting Drug Release From A Matrix Tablet

AI is here. Will you lead or follow? Countdown to EmTech Digital 2019 has begun.

Register now
Want more award-winning journalism? Subscribe to Print + All Access Digital.
  • Print + All Access Digital {! insider.prices.print_digital !}*

    {! insider.display.menuOptionsLabel !}

    The best of MIT Technology Review in print and online, plus unlimited access to our online archive, an ad-free web experience, discounts to MIT Technology Review events, and The Download delivered to your email in-box each weekday.

    See details+

    12-month subscription

    Unlimited access to all our daily online news and feature stories

    6 bi-monthly issues of print + digital magazine

    10% discount to MIT Technology Review events

    Access to entire PDF magazine archive dating back to 1899

    Ad-free website experience

    The Download: newsletter delivered daily

You've read of three free articles this month. for unlimited online access. You've read of three free articles this month. for unlimited online access. This is your last free article this month. for unlimited online access. You've read all your free articles this month. for unlimited online access. You've read of three free articles this month. for more, or for unlimited online access. for two more free articles, or for unlimited online access.