Computing

LED Lights

Forget the sickly green glow. Today's light emitting diodes are bright, white, and coming to a flashlight near you.

  • December 6, 2002
  • By Simson Garfinkel

A disruptive force is sweeping through the world of flashlights. You may not think that flashlights are all that interesting, but hear me out: this is force that will not stop at your utility drawer. Within a few years, when all the world's flashlights have succumbed, the disruptive force will seek new markets. First retail display lights, then office lights, and finally lights in your home will be systematically removed and replaced with something better.

The light-emitting diode (LED) illumination revolution is underway. Cities around the world are replacing incandescent traffic lights with arrays of LEDs, solid-state electronic lights that require less than 10 percent the power of an incandescent bulb to generate the same apparent illumination, and last up to 20 years between replacements.

You'll find the first consumer LEDs in applications where LED lamps' advantages-low weight, long-life, and durability-outweigh their higher initial cost. I bought my first LED lamp in a bicycle shop, and you'll see more in a camping store. There, I found two cute flashlights from Princeton Tec (www.princetontec.com). One, the Attitude, features three ultra-bright white LEDs and claims 150 hours of "burn time" before its batteries must be recharged. The other, the Impact II, has a single LED and 75 hours of burn time. Each measures five inches long, weighs about 80 grams with its four AAA batteries, and fits nicely in my hand. Each will apparently go underwater down to 500 feet. The key difference is that the Attitude has a wider, more diffuse beam, while the Impact II has plastic lens that shapes the light into a beam that travels more than 50 meters (a distance comparable to good incandescent flashlights, but far greater than most LEDs). Another difference is that the Impact has a plastic clip molded into the body, which makes it fit nicely in your pocket, while the Attitude doesn't. Given the choice, though, I'd still take the Attitude-I like the wider beam and the longer battery life. Expect to pay around $20 for the Attitude and $30 for the Impact.

Of course, not every LED lamp is a winner. Consider the Infinity LED task light from CMG Equipment (www.cmgequipment.com). The Infinity is much smaller than the Impact, has a single LED, runs on a single AA battery, and is advertised waterproof only to 10 feet. CMG claims 41 hours burn time for the standard model; if you want a flashlight with roughly twice the brightness and half the time, CMG offers the Infinity Ultra. In my tests, I found the Infinity disappointing: it was so small that it didn't fit neatly in my hand, and the lack of a lens meant that the beam really didn't focus well. Sure, it's a great tiny light, but at $20 for the Infinity and $25 for the Ultra, it doesn't really seem worth the money.

Petzl (www.petzl.com), a reputable maker of climbing gear, offers a variety of LED headlamps. Even if you aren't a climber, you still might find a headlamp useful. By attaching the light to your head, you free up your hands, which makes these lights handy in dark attics, under a car, or even in bed when you want to read at night without bothering your sleeping partner. Petzl's Tikka ($29) has a big elastic headband, while its Zipka ($33) has a retractable strap that pulls into the lamp unit. Both are powered by three AAA batteries and claim 150 hours of burn time. Black Diamond offers a similar head lamp, but it features just two LEDs, compared with Petzl's three.

A note about burn-times: Like regular flashlights, an LED light will get dimmer as the batteries weaken. The folks at Petzl, for instance, say that their lights have a 10-meter range with a set of new batteries, but that range goes down to five meters after 12 hours and two meters after 150 hours.

Print

Related Articles

Turning on LEDs

Solid-state lighting is mounting a challenge to light bulbs.

To comment, please sign in or register

Forgot my password

Advertisement

MAGAZINE

Can We Build Tomorrow's Breakthroughs?

Manufacturing in the United States is in trouble. That's bad news not just for the country's economy but for the future of innovation.

Sponsored Content

Technologies from National Instruments

Adding Data Logging
Log measured data to a file and open it in Microsoft Excel

> Click here for more National Instruments Videos <
Whitepaper

Temperature Measurements with Thermocouples: How-To Guide

This document is part of the “How-To Guide for Most Common Measurements” centralized resource portal. This tutorial provides a detailed guide for measurement and device considerations to take temperature measurements using thermocouples. Get an introduction to thermocouples, which are inexpensive sensing devices widely used with PC-based data acquisition systems. Also review some specific thermocouple examples and learn how thermocouples work and ways to integrate them into a data acquisition measurement system.

View full PDF > Listen to story >
Find us on Youtube

Videos

A Robot Recruit that Can Do It All

More

Advertisement

Technology Review Lists

TR50

Our list of the 50 most innovative companies, including the following:

Crowdcast

IBM

Apple

Lattice Power

More

Advertisement

Facebook

Advertisement